[img]
http://img535.imageshack.us/img535/3214/img0698b.jpg[/img]
[img]
http://img209.imageshack.us/img209/4648/img0700h.jpg[/img]
===========================
Stats:
===========================
Kerskuri G3 Mod
COG=COP=COSS
Length: 20cm
Weight: about the same weight as a Kuzu I think, I am not quite sure
Style: Single Sided
Writing-Mechanism: N/A
Ink-Type: N/A
Estimated-Cost: quite expensive
===========================
Materials List:
===========================
1x Pilot G3 (Metal or Plastic doesen´t matter)
1x Hyperjell
1x Uni Impact Rt/ Signo Broad/ Knocktype
2x Pentel Hybrid Gel Grip
2x Signo Broads
1-2x Sailor
1x Hi Tec-c/ G1
1x Gripmatic
2 Rings Anyball Grip
2x Inlays
===========================
Altough my English isn´t that good I hope you are able to understand everything. When you have questions post them in this thread or send me a pm. Anyways, let´s get started.
[img]
http://img337.imageshack.us/img337/3452/img0675o.jpg[/img]
Take apart the G3, saw the thread off and file down all the bumps (like in the Firefly G3).
[img]
http://img137.imageshack.us/img137/9135/img0672v.jpg[/img]
Now tape the back of the G3 body so the Hyperjell Cap would fit on snuggly and insert an inlay(Size: 8,6cm x 2,5cm but you can only see 8,0cm x 2,0cm!)
[img]
http://img190.imageshack.us/img190/4536/img0676kz.jpg[/img]
Cut the Hyperjell front at 2,5 cm like it´s shown in the picture and file down the bumps.
[img]
http://img138.imageshack.us/img138/5676/img0680g.jpg[/img]
Take a piece from the Signo Broad inktube and tape it, so it would fit nice & snuggly inside the G3 body and the Hyperjell frontpart.
[img]
http://img39.imageshack.us/img39/8712/img0681z.jpg[/img]
Put the taped inktube piece inside the G3 and the Hyperjell frontpart like it´s shown in the picture. Also add a gripring from the Hgg and 0,7 cm of Signo Broad grip to the front.
[img]
http://img684.imageshack.us/img684/4976/img0678d.jpg[/img]
Attach one Signo tip to the Hi Tec-c/ G1 tip.
[img]
http://img594.imageshack.us/img594/6362/img0683iq.jpg[/img]
Attach the tips to the front and tape them so everything is secure and won´t fall apart.
[img]
http://img207.imageshack.us/img207/1371/img0684bo.jpg[/img]
Put a HGG grip over the front(It will be helpfull when you stretch it bevore)
[img]
http://img708.imageshack.us/img708/671/img0686xi.jpg[/img]
Take a 1,5 cm long piece from the Signo Broad Grip(I used HGG grip) and put it over the tips.
[img]
http://img21.imageshack.us/img21/3691/img0688hm.jpg[/img]
Now take the Uni Impact RT/ Signo Broad/ Knocktype grip and make a gripcut.
[img]
http://img641.imageshack.us/img641/1976/img0689jh.jpg[/img]
Put the gripcut over the HGG grip and place 6 rings of Sailor grip in front of it. If you did this you are finished with the front and the body of your Kerskuri G3. Now let´s start with the back.
[img]
http://img819.imageshack.us/img819/8905/img0691iu.jpg[/img]
Take the hyperjell cap do a clipcut and remove the little rubber thing.
[img]
http://img577.imageshack.us/img577/1849/img0692gc.jpg[/img]
Now take the Gripmatic and cut a 2,5 cm long piece from the front.
[img]
http://img444.imageshack.us/img444/1525/img06941.jpg[/img]
Take two rings of Anyball grip and put it inside the Gripmatic frontpiece.
[img]
http://img204.imageshack.us/img204/9237/img06931.jpg[/img]
Attach one HGG tip to the second signo tip and add a little bit of tape like it´s shown in the picture(Use teflon tape, glue, ...)
[img]
http://img692.imageshack.us/img692/1627/img06952.jpg[/img]
Screw the tips on the Gripmatic frontpiece.
[img]
http://img196.imageshack.us/img196/8853/img06961x.jpg[/img]
Cut 2,9 cm from the second Hgg Grip and put it over the Gripmatic front piece.
[img]
http://img528.imageshack.us/img528/1738/img06971.jpg[/img]
Add an insert(Size: 3,0 cm x 3,4 cm) and put the whole thing into the Hyperjell cap.
Put the Hyperjell cap on the back of the G3 body and you´re done.
[img]
http://img705.imageshack.us/img705/2092/img07021.jpg[/img]
Have fun, hope you like it .
ps.: Credits for the Inlay go to iVodka.