So, nun mal ein leichter Mod, welcher sehr leicht zu bauen ist.
Die Mats dazu bekommt man eig. auch alle recht einfach.
Halé Mod
[img]http://66.90.122.10/mayu/pictures/halemod/13.jpg[/img]
Stats
Length: 20-20,5cm
Weight: 14g
COG: COG=COP
Writing-Mechanism: N/A
Estimated cost: N/A
___________________________________
Materials List
Doppelfasermaler (Caps)
Pic 01 – Pic 02
HGG 2x (Caps)
Signo Broad 2x (Tips)
SuperPirate Body 1x
Anyball Grip 2x
If you're interested in these "Doppelfasermaler" - pack is 3,49€ (12 pens) - 4,25$ - i can send you these, they are amazing for modding imo.
Basic tools: Knife, Lighter, Hammer, Something like the tip in my picture
As you can see from the material list, this colors of this mod are highly configurable – make the mod look like you like it!
___________________________________
Step 01
Gather your Materials - HGG 2x | Signo Broad 2x | Super Pirate Body | Anyball Grip 2x | VIVESS Doppelfasermaler
[img]http://66.90.122.10/mayu/pictures/halemod/01.jpg[/img]
Step 02
Remove the parts we need for this Mod - HGG Caps 2x | Signo Tip 2x | Doppelfasermaler Caps 2x | SP Body |Anyball Grip 2x
[img]http://66.90.122.10/mayu/pictures/halemod/02.jpg[/img]
Step 03
Remove the Clips from the HGG Caps and cut it so no edges are left - no matter how it looks in the end. Also remove the Sticker
[img]http://66.90.122.10/mayu/pictures/halemod/03.jpg[/img]
Step 04
Put the Signo tips into the HGG Caps like shown.
[img]http://66.90.122.10/mayu/pictures/halemod/04.jpg[/img]
Step 05
Hammer out the inside of the Doppelfasermaler Caps. Keep both parts
[img]http://66.90.122.10/mayu/pictures/halemod/05.jpg[/img]
Step 06
Cut the inside of the Cap, so you have a 0,5cm long piece of the end
[img]http://66.90.122.10/mayu/pictures/halemod/06.jpg[/img]
Step 07
Cut the little leftovers around the Plug
[img]http://66.90.122.10/mayu/pictures/07.jpg[/img]
Step 08
Push the Plugs into the Signo Tips, It should fit perfect! Push them all in!
[img]http://66.90.122.10/mayu/pictures/halemod/08.jpg[/img]
Step 09 (sry for bad quality!)
Cut the Anyball Grips like shown. Start on the bigger side and cut 7 and 1 ring
[img]http://66.90.122.10/mayu/pictures/halemod/09.jpg[/img]
Step 10
Push the HGG Cap into the Anyball Grip
[img]http://66.90.122.10/mayu/pictures/halemod/10.jpg[/img]
Step 11
Pus the HGG Cap into the Cap of the Doppelfasermaler Cap like shown
[img]http://66.90.122.10/mayu/pictures/11.jpg[/img]
Step 12
Add 1 Ring of Anyball on each side and add the Caps - your very own Halé; Mod
[img]http://66.90.122.10/mayu/pictures/halemod/12.jpg[/img]